23
Oct
Sebelum halloween tiba, tidak ada salahnya untuk membuat kerajinan tangan bersama anak, selain membuat anak makin kreatif tentunya akan menambah quality time bersama anda
This materials list contains affiliate links for products I recommend.
•Plastic Trick or Treat Pumpkin
•Rope
•Tan Yarn
•Light Colored Duct Tape
•Masking Tape
•Black Top Hat
•Black Sunglasses
•Scissors
•Hot Glue and Glue Gun
Cut off the existing black plastic handle on the pumpkin. Replace it with rope. Measure it, depending on the height of your child.
Next, unwind the spool of yarn around a chair back several times. Pull it off and cut only one end.
Lay out a piece of duct tape about 10” long. Lay the looped end of the yarn onto the duct tape.
Tape it around the mid-section of the pumpkin.
Repeat these steps and do the other side.
Note: I happen to have blue duct tape, so that’s what I used. I would recommend choosing a light colored duct tape so that it doesn’t show through the yarn.
Repeat the steps above again, but in shorter strips of duct tape. This time, tape them around the rim of the pail.
Next, lift up the first layer and cover the face with masking tape. This will help hide the face behind the yarn. For mine, I also covered the blue duct tape with masking tape.
Cut the top off of the top hat. Place it on top of the pumpkin allowing the rope to come through. It will fit snuggly on the pumpkin. Use duct tape to tape the hat to the pumpkin as shown.
Source Article : https://www.diyinspired.com/cousin-diy-trick-treat-pail/ [ ... ]
Read More
This materials list contains affiliate links for products I recommend.
•Plastic Trick or Treat Pumpkin
•Rope
•Tan Yarn
•Light Colored Duct Tape
•Masking Tape
•Black Top Hat
•Black Sunglasses
•Scissors
•Hot Glue and Glue Gun
Cut off the existing black plastic handle on the pumpkin. Replace it with rope. Measure it, depending on the height of your child.
Next, unwind the spool of yarn around a chair back several times. Pull it off and cut only one end.
Lay out a piece of duct tape about 10” long. Lay the looped end of the yarn onto the duct tape.
Tape it around the mid-section of the pumpkin.
Repeat these steps and do the other side.
Note: I happen to have blue duct tape, so that’s what I used. I would recommend choosing a light colored duct tape so that it doesn’t show through the yarn.
Repeat the steps above again, but in shorter strips of duct tape. This time, tape them around the rim of the pail.
Next, lift up the first layer and cover the face with masking tape. This will help hide the face behind the yarn. For mine, I also covered the blue duct tape with masking tape.
Cut the top off of the top hat. Place it on top of the pumpkin allowing the rope to come through. It will fit snuggly on the pumpkin. Use duct tape to tape the hat to the pumpkin as shown.
Source Article : https://www.diyinspired.com/cousin-diy-trick-treat-pail/ [ ... ] 
Supplies: balloon, liquid corn starch, strips of newspaper. And for decorating the piñata after it dries, you will need white paint, tissue paper, black felt, and Elmer’s glue.
2. Blow up your balloon and begin dipping strips of newspaper in liquid corn starch. Lay the strips on the surface of the balloon (you want the strips wet, but not soggy). Continue doing this until the balloon is totally covered. 3. After your balloon has been drying for about a day, cover the newspaper in a coat of white paint. This will hide any newsprint that may want to peek out. After the paint dries, carefully pop the balloon inside of the newspaper.
4. Begin glueing tissue paper around the base of the balloon. You may need more than on piece to make it wrap all the way around.
5. After you have glued 3 or 4 long tiers on, start back down by the base of the balloon and begin the same process with thinner strips of tissue paper. You will need a large circle to finish off the top. 5. When all of the strips have been glued down, go back to your long layers at the bottom and cut them into fringe.
6. Cut faces shapes out of felt and glue them down. You’re all done!
Source Article : https://abeautifulmess.com/2012/10/ghost-family-pinata-party.html [ ... ] 
Supplies:
–black pom poms (I used 2″ pom poms but they can be varying sizes)
–black pipe cleaners (4 per spider)
–hot glue gun
–small googly eyes
–bakers twine and large eye needle
–yarn for tassels
First, take two pipe cleaners and twist them together in the middle, creating an “X” shape. Fold the X in half so you have 4 legs of equal length. Repeat with two more pipe cleaners so you have two sets of legs. Next, part the furryness of your pom pom and put a large drop of hot glue near the center. Stick the twisted side of your legs into the glue and allow the glue to set. Repeat on the opposite side with your second set of legs. Next, use a small drop of glue on the back of each googly eye and attach them to your spider face. To finish, bend your legs upwards right next to the base of the pipe cleaners, then bend them back down about 1/3 of the way up the leg. Bend the last 1/2″ of each pipe cleaner back up again to create the feet and repeat on the other side.
To hang your garland, thread some baker’s twine through a large eye needle and sew through each spider’s core so they are suspended on the string (try and get them near the top of their core so they don’t flip upside down). Once all your spiders are threaded, use some hooks to hang your garland in your desired spot and make some yarn tassels to hang on each end. That’s it!
Article Source : https://abeautifulmess.com/2018/10/easy-spider-garland-diy.html [ ... ] 
This tiny pumpkin diorama is the perfect office desk decor. It says “I appreciate Halloween” without completely letting your freak flag fly. Subtlety is key with the ‘ween decor.
Materials and Tools:
glitter
permanent marker
paint brush
black acrylic paint
spoon
knife
mini pumpkin
moss and dried foliage
model people
Grab your materials. It’s time to whip out those fine motor skills!
1. Make a rectangle using permanent marker.
2. Using a serrated knife, carefully cut along your lines. Remove the seeds with a spoon, making sure to scrape away as much of the loose pumpkin fibers as possible. Pat the inside of the pumpkin dry with a paper towel.
3. Paint the inside of the pumpkin with the black acrylic paint and add glitter while the paint is still wet. Allow the paint to dry completely (about two hours) before moving onto the next step.
4. Place a layer of moss on the bottom of the pumpkin and trim your dried botanicals to fit inside of the pumpkin. Pierce twigs into the flesh of the pumpkin to keep them in place.
5. When you’re happy with your composition, place a few model people into your diorama. I purchased jogging figurines and policemen to create a spooky chase scene.
6. That’s all it takes to make a spooky mini Jack-o’-Lantern that’s perfect for your desk.
Article Source : https://www.brit.co/stranger-things-are-happening-in-this-diy-mini-jack-o-lantern-diorama/ [ ... ]